Techne Hybrigene Bedienungsanleitung

Hybrigene Hybridisation oven OPERATOR’S MANUAL Issue 7 07/2014

10 3. Placer l’appareil sur une surface plane ou si nécessaire sous une hotte d’aspiration, veiller à ce que les trous d’aération situés sous l’a

11 SICHERHEITS- UND INSTALLATIONSINFORMATIONEN Lesen Sie diese Anleitung vor Verwendung des Hybrigene bitte sorgfältig durch. ACHTUNG HOHE TEMPE

12 I Netzschalter Ein O Netzschalter Aus Ersatzkabel Bei einem eventuellen Austausch des Netzkabels wird ein Kabel vom Typ H05V

13 INFORMAZIONI SULLA SICUREZZA E L'INSTALLAZIONE Leggere attentamente il presente manuale prima di usare il Hybrigene. AVVERTENZA Le ALTE

14 3. Collocare l'unità su un banco piano idoneo o in una cappa aspirante se necessario, assicurandosi che gli sfiati delle prese d'ar

15 INFORMACIÓN DE SEGURIDAD E INSTALACIÓN Lea atentamente este manual antes de utilizar el Hybrigene. ADVERTENCIA LAS ALTAS TEMPERATURAS SON PELI

16 3. Sitúe la unidad sobre una mesa plana o en una campana de laboratorio si es necesario, y asegúrese de que los orificios

17 CONTACT INFORMATION For technical, sales or servicing information, contact your local Techne dealer or: UK Bibby Scientific Ltd. Beacon Road

18 SPECIFICATIONS Tube capacity 4 (large and small in any combination) 16 mini tubes (when using the FHB61 mini tube holder) 64 x 15ml tubes (i

19 INSTALLATION See also the sections on Safety and Installation. 1. Place the unit on a suitable flat bench or in a fume cupboard if required,

2

20 FHB4DSTK: Stacking and wall mounting kit for two units Description Part code Quantity Wall Bracket 6105214 1 M4 x 8 Pozi Pan Screw 6008652

21 8. Put the hybridisers in the position you want to use them. 9. Position the wall plate and mark the position of the holes. 10. Use the app

22 SETTING THE TEMPERATURE Controller display 1. Press the ’P’ button on the controller and the set temperature will be displayed. 2. To in

23 HYBRIDISATION TUBES The hybridisation tubes are manufactured from durable thick borosilicate glass with a non-drip design. The tubes must be ch

24 Mini (4 x 32mm) tube assembly (FHB41 and FHB61) The mini tubes must be used in the FHB61 multi-tube holder. Unscrew the end cap of the tube. P

25 INSTALLING THE HYBRIDISATION TUBES 1. Pre-heat the oven to the required temperature. 2. Insert the tubes or tube holder into the Hybrigene e

26 DO NOT TIP THE TUBE SO THAT THE COLOURED END IS DOWN AS THIS WILL CAUSE A SPILLAGE. 3. The unit has been designed to conform to international

27 ADDITIONAL INFORMATION Note that this equipment should only be dismantled by properly trained personnel. Removing the outer cover

28 SPARES AND ACCESSORIES The following spares and accessories may be purchased from Bibby Scientific Ltd. or their dealers. All Techne tubes ar

29 DECLARATION OF CONFORMITY

3CONTENTS INTRODUCTION ... 5 BEFORE USE...

4DECLARATION OF CONFORMITY ... 29

5INTRODUCTION Please read all the information in this manual before using the unit. The Techne Hybrigene hybridisation oven is ideal for

6BEFORE USE Before using the Hybrigene please make sure you have read this manual carefully. If there is any doubt relating to the proper use o

7SAFETY AND INSTALLATION Please read all the information in this manual before using the Hybrigene. WARNING HIGH TEMPERATURES ARE DANGEROUS: they

8 I Mains Switch On O Mains Switch Off Replacement cable Should the mains lead need replacement, a cable of 1mm2 of harmonized code H05VV-F

9SÉCURITÉ ET CONSIGNES D’INSTALLATION Veuillez lire attentivement toutes les instructions de ce document avant d’utiliser le Hybrigene. AVERTISSE